Home > Pro Tools > Pro Tools Error Message Problem Detected With Audio Clock

Pro Tools Error Message Problem Detected With Audio Clock

Contents

The clock source in "Hardware" is set to internal, as usual. If I'm able to fix it I will share my findings here. Trending Now Justin Bieber Brad Pitt Ben Roethlisberger Steven Yeun Luxury SUV Deals Rheumatoid Arthritis Symptoms Cecilia Hart 2016 Cars Kevin Meaney Tennessee Titans Answers Relevance Rating Newest Oldest Best Answer: Takes just a minute and then you should be good to go. my review here

Everything is up to date... Share Quote 19th November 2013 #5 amost Lives for gear I have the same issue Share Quote 19th November 2013 Mark Pezzelato 9.269 προβολές 3:50 Pro Tools Playback Engine Reset: Trouble Shooting Tip - Διάρκεια: 4:38. You can change this preference below. Κλείσιμο Ναι, θέλω να τη κρατήσω Αναίρεση Κλείσιμο Αυτό το βίντεο δεν είναι διαθέσιμο. Ουρά παρακολούθησηςΟυράΟυρά παρακολούθησηςΟυρά Κατάργηση όλωνΑποσύνδεση Φόρτωση... Ουρά παρακολούθησης Ουρά __count__/__total__ Pro No amount of turning down in your software will help. original site

Problem Detected With Audio Clock Pro Tools 10

recordingrevolution 186.909 προβολές 4:18 External word clock syncing for digital recording and Digital keyboard sounds - Διάρκεια: 1:13. This error is intermittent and so far has only been seen when opening multiple (10-15) sessions that each vary in sample rate from the previously opened session. I know my laptop isnt the best, but even on my desktop that isnt as good it worked fine...

  • You can only upload photos smaller than 5 MB.
  • Cheers Source(s): http://www.digidesign.com Techgique · 7 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse Don't listen to these guys, they clearly
  • It's a lot slower and lower pitched than the original recording.
  • It's after your mic and gain, but before your recording software.
  • I have a problem with the sync device of avid and the Digidesign 192, technically when you plug in the the serial host of the SYNC device to the PRO TOOLS
  • Anybody know?
  • After my extensive research I also found its the most affordable way to go in the long run.
  • Now when I do it, it won't seem to change at all.

What do you mean by 'mix'? However, I noticed that Digidesign (now AVID) is not bragging a lot about this expansion feature so I said to myself Ok, where's the catch? loss of clock)? Tools 12"clock I check the TC NEAR Control Panel and the sample rate and clock source are both correct.

Forum New Posts FAQ Calendar Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders For the Record News Blogs Articles Editorial Reviews User Reviews Classifieds Advanced Search Forum Pro Tools Clock Source See Control Panel Follow us on inSync Facebook Twitter YouTube Instagram FREE Catalog and other Sweetwater publications! help! There is a distortion that happens when recording vocal and it is there on playback.We have tried changing buffer size, cables, different mics and leads, how close I am to the

sorry… im not from usa or another country where english is the language so … im sorry if im writting in the wrong way. Clock Source Pro Tools 11 I'm running win7 in compatability mode(32bit). I can't bounce anything to disc without the tempo and pitch of the song changing. They keep all the different parts of a working studio in sync with each other so there's no lag or jitter which can show up as unwanted clicks and pops when

Pro Tools Clock Source See Control Panel

help! Y General Topic Guitar Recording / Editing Headphones How to? Problem Detected With Audio Clock Pro Tools 10 I want the sequenced drum machine parts to lock exactly with the click plug-in tempo as well as making sure the measures sync up as well. Clock Source Pro Tools If you use a USB cable make sure it is connected directly to a high speed port.

May 4th, 2011 Reply Graham Davo - It sounds like a sample rate issue perhaps. this page Now I'm guessing that you probably don't have an eSATA card, but it seems to me that Pro Tools could be mistaking some conflict within your PC as an audio clock Thanks Digidesign. Hwy 30 W Fort Wayne, IN 46818 Get directions Toll Free (800) 222-4700 Español (800) 222-4701 Local (260) 432-8176 Fax (260) 432-1758 Email us Phone & Music Store Hours 9–9 Monday–Thursday Pro Tools 8 Audio Clock Error

OBEDIA 46.422 προβολές 4:18 Audio & MIDI Hardware Setup (Pro Tools 11 Explained) - Διάρκεια: 4:34. I havent tested in a while.. Check that your clock source and sample rate are correct. " Everything is set to 44.1 and 24-bit. http://bsdupdates.com/pro-tools/pro-tools-8-audio-clock-error.php Privacy Policy Imprint & Terms of Use Sitemap © 2015 MUSIC Group Innovation DK A/S Υπενθύμιση αργότερα Έλεγχος Υπενθύμιση απορρήτου από το YouTube, εταιρεία της Google Παράβλεψη περιήγησης GRΜεταφόρτωσηΣύνδεσηΑναζήτηση Φόρτωση... Επιλέξτε

Any way to save the settings? The Current Playback Engine Does Not Support A Sample Rate Of 48khz what do i do??? This is the result of confusion on which device (your interface or lightpipe device) is acting as the clock source.

And I realize that this is not much help, but possibly could help you touble shoot by checking other connections or hardware in your PC.

One last thing, Pro Tools is not supported on Vista 64, so make sure you are using 32 bit. I had a weird issue once where the sample rate was not right... Password Register FAQ Today's Posts Search Search Forums Show Threads Show Posts Tag Search Advanced Search Go to Page... They're coming along slowly but surely.

Also what drive are you writing your music too? http://www.myspace.com/cswstudio www.capricornsoundworks.com The better I drink...the more I mix..... Madison Pro Audio 3.049 προβολές 1:31 Pro Tools Tutorials - Vocal Recording Studio Tips in Pro Tools - Διάρκεια: 9:57. useful reference So, I'll go with the 003 and expand following your recommendations.

Using an actual ADAT as the interface, with clock set to ‘optical'. You can only upload files of type 3GP, 3GPP, MP4, MOV, AVI, MPG, MPEG, or RM. Is your mbox gain too high? We've hooked up our digi 002 with a behringer pro-8 through a lightpipe cable.

God Bless! By using this site, you agree to our use of cookies. The time now is 07:15 AM. Check that your clock source and sample rate are correct." I checked the source clock, it is internal.

Thanks again Graham. To fix your problem you need to install PC Health Boost, download it here for free: http://www.pcboostcleaner.com It's very light and it's the only antivirus/cleaner with a 99.99% detection rate; it's I didn't change a thing between this morning and now; don't know why it suddenly won't play!