Reinstall Controller personality file from Protools installer CD-ROM. Reduce the number of active Plug-ins. Find all posts by Seeee #5 10-25-2004, 02:32 PM Infa Member Join Date: Jun 2004 Location: San Francisco, CA. In 1996, Campbell won the Pulitzer Prize for Criticism. my review here
Current harddrive requirements for your Pro Tools system are available at http://www.digidesign.com/compato under the Harddrive Minimum Requirements Section. -6042 errors can occur when writing to unsupported volumes (Jazz, Zip, USB, Network Then repair permissions once booted from the volume. This error may also pertain to an incompatibility problem with DSP chip latency between multiple HD Accel DSP cards. And see if top -au or Bigtop (part of CHUD) shows anything out of the ordinary.
biggles. "illegitimis non carborundum" Reply With Quote Quick Navigation Sweet Sounds Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums The Beginning Repair and Troubleshooting Tips DAE error -6042 during playback when scrolling, adjusting faders, or opening/closing Plug-In windows on a G3 (beige). DAE ERROR -6042 Thomas Chiu 003, Mbox 2, Digi 002, original Mbox, Digi 001 (Mac) 4 10-09-2001 03:09 AM error 6042 swivelhead 003, Mbox 2, Digi 002, original Mbox, Digi 001 It includes Προεπισκόπηση αυτού του βιβλίου » Τι λένε οι χρήστες-Σύνταξη κριτικήςΔεν εντοπίσαμε κριτικές στις συνήθεις τοποθεσίες.Επιλεγμένες σελίδεςΣελίδα ΤίτλουΠίνακας περιεχομένωνΕυρετήριοΠεριεχόμεναLesson 1 Pro Tools HD Hardware Configuration1 Exercise 1 Pro Tools HD
The system has run without a hitch for the last 6 months since PTLE6. Disable QuickPunch to see if the session plays back. - Disable the Record Online at Insertion / Selection Preference. - Automation, especially of TDM plug-ins, requires PCI bandwidth also. Removing the cards resolved the issue in each case. website here Need Help?
In 2003 he was a Senior Fellow in the National Arts Journalism Program at Columbia University. Apply Today Subject to credit approval. Disable 3rd party FireWire extention. Computers are picky!
Note: the front cover design has changed on both units to allow for easier filter change, slot order is only reversed for the 13 slot, it remains the same for the https://www.gearslutz.com/board/music-computers/355123-pro-tools-error-6042-a.html Hmmn! Posts: 1,023 Re: DAE Error 6042 This error has many potential causes, all of which relate to overtaxation of your computer's PCI bus. Reset PRAM.
XThread Tools Show Printable Version Email this Page Search this Thread Advanced Search Register Help Remember Me? this page The time now is 05:12 AM. Seat all cards and cables firmly. The information provided below should resolve most occurrences of the error. * Make sure that all system hardware is compatible by checking the online compatibility page for your specific Pro Tools
DAE Error-35 OMFI Media Files folder on a Unity volume contains illegal characters. Please use Protools 6.1 CD. Article #3626 Updated on Apr 17, 2012 at 5:22 PM DAE error -6042 during playback in Pro Tools. get redirected here This error will only occur the first time Unity Volume is accessed.
Bad Volume Bitmap on audio drive. DAE Error-9019 When using Protools Avid MediaNet. In OS 9, which is on the native ATA drive, recording to a hosted drive works OK!
Replace TDM flex cable. I really thought that I'd covered that possibility early on when I'd stripped things down to just the Digidesign card and one drive on the native bus, but there you go. Error -36 Unable to create new audio file on drive because of I/O error. Try: FAQ Index Guide & Mac Pro Reference Reply With Quote 09-05-2004,01:15 PM #5 biggles View Profile View Forum Posts Guru Moderator Join Date Jun 2003 Location UK Posts 1,317 thanks
Bit 3 reversed the slot ordering in the 13-slot chassis at serial #198487 (around the middle of 1999). extensions. If in 32 voice mode, try switching to 64 voice mode and make sure that the voice allocation is set to auto. useful reference I couldn't see anything unusual going on with Activity Monitor or top.
Thanks Michael Share Quote 6th January 2009 #2 DSD_Mastering Lives for gear My Studio Error -6042If you repeatedly encounter -6042 errors, open the System Usage window and Try suspending automation globally or per-track. - On a Mix system with Pro Tools 5.1.3 and higher you can take advantage of Voice Load Balancing if there is more than one Check permissions settings on all record drives. The video monitor was plugged into an output that we dont normally use..i moved it back and now its fine.
Try suspending automation globally or per-track. * On 13 slot chassis make sure the J2 jumper on the host card is spanning pins 1-2 and not 2-3. Campbell has taught at the Harvard Graduate School of Design, the Boston Architectural Center, and the University of North Carolina. Go to System Preferences>Energy Saver>Options,and set Processor Performance to Highest. I am able to record for alittle while and then the system tells me that there is a problem with the pci bus and voicing (error 6042).
Mac Guide - Mac OS X 10.8 Mountain Lion Optimizations and Troubleshooting Pro Tools 12 System Requirements Highest Rated Articles AAF Export is cancelled with the message AAF export NN is So I decided to do a little research reading for hours the duc.avid.com support website. No M$ allowed on my DAW Mac. You can check the maximum supported track counts for your Pro Tools system at http://www.digidesign.com/compato in the Minimum Hard Drive Requirements section. * In Pro Tools, you can check the current
Reseat all cards and cables. The system has run without a hitch for the last 6 months since PTLE6. Of course, I don't have the "fewer voices" option, and the Playback Engine is set to use 85% CPU. DAE Errors-6089-6085-9093 Increase or decrease the Hardware Buffer size.
What I have found is that you should NOT use the AC adapter for the Mbox 2 Pro unless the Firewire port on your computer doesn't supply power - which I Reply With Quote 09-06-2004,03:32 AM #9 biggles View Profile View Forum Posts Guru Moderator Join Date Jun 2003 Location UK Posts 1,317 M.Brane, I couldn't agree more, but this was a Here's a recording solution to help.My 003/002 interface is losing connection with Pro Tools 9.When I create a new session using the I/O Settings Selector in Pro Tools 9 my Outputs DAE Error-9162 Digilink cable is incorrectly connected to Core/Accel cards.
What seems off is that why would this happen on sessions that previously worked fine... When I watch the pci usage it is quite low until a very heavy spike that stops everything. Share Quote 7th January 2009 #4 Keire Lives for gear Remove TC Tools 3.7 from the plug-ins folder and install 3.6 DAE Errors-7201-7202-7203-7204-7205-7206 Hardware configuration problem.