Home > Printer Error > Printer Error Code 52

Printer Error Code 52

Goldwasser. If you can shine a flashlight through it, it's probably ok. (From: Ralph Wade Phillips ([email protected]).) About 50% dead laser and 50% bad DC controllers (photoreceptor dies, or interface chip it Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize.2. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, click site

If the error persists, replace the laser/scanner. Turned it off for a few minutes. HP LaserJet Error Codes 50-59 Message on printer displayWhat it meansWhat to do 50.X FUSER ERROR A fuser error has occurred. 1. HP LASER PRINTERS 8100, 81501.Laser scanner error/start up/rotation error2.Replace laser scanner ass'y.3.Replace D.C. find more info

A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)..) appears.. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? Reseat cables to the laser/ scanner and engine controller. 4. Turn the printer off, and then turn the printer on. 2.

The Printer Works: 1-800-235-6116. (These people have the coolest catalog in the business!) Laser Impact: 1-800-777-4323. If after replacing the laser/scanner, the message persists, replace the ECU. Turn the printer off, and then turn the printer on. 2. Temporary error.Laser scanner error/start up/rotation error 2.

Plug the printer into a wall outlet and see if this resolves the problem. 3. Defective dc controller. Ah - didn't know this!  Certainly I will be contacting our vendor to get this replaced. 0 Pimiento OP markanthonyohnikian May 21, 2014 at 6:43 UTC 1st Post imp source HP LASER PRINTERS 3SI, 4SI, 4V 1.

The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 51.X PRINTER ERROR A loss of beam-detect Replace the formatter and/or firmware DIMM. 4. Turn the printer off and then on. 3. Check the FFC connection between the formatter and the scanner. 5.

See ASP.NET Ajax CDN Terms of Use – http://www.asp.net/ajaxlibrary/CDN.ashx. ]]> original site controller HP LASER PRINTER 4500, 4550 1. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations You may want to try this too: http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/error-code-52-intel-i5-processor...Regards.

You must remove the ECU in order to verify this connection.5. get redirected here Join Now I'm a little peeved that our next replacement option for the P2055's are these odd HP LaserJet 400's (M401DN) with a pop-up screen. The page containing the error will automatically be reprinted. 1. Any ideas, anyone, please?

  • Plug the printer into a wall outlet and see if this resolves the problem. 3.
  • Press the SELECT button to continue.3.
  • Verify that the scanner motor connector is firmly seated in connector J402 on the ECU.
  • The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 55.xx PRINTER ERROR alternates with CYCLE POWER
  • Turn the MFP off, and then turn the MFP on. 3.
  • Turn the printer off, wait 10 minutes, and then turn the printer on. 2.

controller and back to scanner. Especially when it only lasts a year. Also check the optical fiber running from the laser scanner housing to the dc controller: Sometimes it goes bad or the end gets dirty. navigate to this website Replace the fan.

Replace laser scanner. 5. Turn the printer off, and reseat or replace the specified DIMM. 2. Turn the power off and then turn the power on again.4.

If after replacing the contact image sensor, the error persists, replace the formatter.

The main reason I found it difficult to locate the scanner assembly using the HP diagram is because they have a bold warning on the diagram and printer warning that the This can also be the shutter tab on the print cartridge. Scanner motor problem. 3. Technicians answer the phone and help customers with printer problems.

Try connecting the product to a different power source or surge protector. 6. First off, the screen is just unnecessary (or at least the pop-up variety), but that's not my problem. Not a member? http://bsdupdates.com/printer-error/printer-error-code-49-3048.php Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10

The connections fail far more often than the $canner. Solution: 1. HP LASER PRINTERS 2P, 2P+, 3P 1. Pull the sealing tape tab to remove the strip. 3.

Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you! The manual states that this error is a 'scanner fault'. Try connecting the product to a different power source or surge protector. 6. HP LASER PRINTERS 4L, 4P, 5P, 5L, 5SI 1.

Our printer works ok most of the time, but then sometimes it just stops printing with this "52 Scanner Error".  Then it says to turn it off and back on again, You can even send us your printer for repair. Check the laser/scanner cable connections.2. connected on the formatter and on the laser/scanner. 3.

Replace the environmental thermistor. 4. All Laser Service is offering the part for $69.95. The machine goes through its warm up routine OK but if I do an internal font printout or print from a PC then it sits quitely for about ten seconds, then A temporary printing error has occurred. 52.0 = Scanner error. 52.1 = Scanner startup error 52.2 = Scanner rotation error 2.