Home > Printer Error > Printer Error Code 49.ff04

Printer Error Code 49.ff04

Sending Using an outdated .JAR file or a .JAR file for another product. Examples of items that have been responsible for errors in the past For each category below, items have been provided on specific items that have been known to cause errors in As soon as the memory count begins, hold down the Stop button until all three control panel lights flash once and then remain lit. In all circumstances, the only way to bring the device back to a READY state is to power cycle the unit. click site

Have a manual for HP LaserJet 2420dn Printer? Right before the printer would die, we noticed that a DHCP NAK packet had been sent. Mo Reez 55.544 προβολές 1:57 Printer problem M1522nf - Διάρκεια: 2:05. Move to step 6.

When you upgrade the firmware for the formatter it also upgrades the firmware on the embedded nic card. Non-HP DIMMs are not supported by HP and may cause this error. If you were to remove the NIC, and install another component, eg. by unknown on Nov 9, 2010 at 9:26am Add comment Please sign in to comment Instead of saying "me too", don't you think you should tell us if you tried anything

  • I also took all the port security off the ports and seem to help for a couple days.
  • Press the Down arrow until you see "Set RFU Error Off".
  • by unknown on Mar 23, 2010 at 10:01am Add comment Please sign in to comment 0 dmsMikecheck out this link....it may give you some understanding.I am not too familiar with the
  • If you turn on without the usb or network connected and it comes to the error, then you are having a issue with your formatter and most likely it will need

Use the SERVICE menu to restore the serial number and page counts. Power up and try again. From within Wire Shark, we were able to see that the packet came from a personal router that had been plugged into our network. Mostly because of components shifting during transfer from oven to counter. 2nd, If you do not make a proper stand for the formatter to hover on, you can risk components sticking

Once all components have been removed, print a Configuration page and Menu Map. by unknown on Aug 8, 2012 at 12:48pm Add comment Please sign in to comment 0 Fixed it by disabling Network Protocols. Already a member? http://www.fixyourownprinter.com/posts/39866 remove network card from printer and instert it back - or try to turn printer on without it Question about HP LaserJet Printers & Copiers 1 Answer 49-ff04 error 49-ff04 error

Remove all memoryDIMM's or third-partyDIMM's from the printer.(Do not remove thefirmwareDIMMin slot J1.) Remove allEIOdevices. Write down this name as it will be needed later. Black or blank pages may be caused by a defective power supply,DC controller, laserscanner assemblyor even aformatter. It is also important to have the machine watched closely after the accessories have been reattached to determine if the condition that initiates the error can be document by an end

Plug the usb or network cable back in with the printer on ready and see if the error is gone. http://www.justanswer.com/printers/2ugwu-does-message-49-ff04-service-error-showing.html If the error continues, then (Contact your regions HP Customer Care Center). If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. An example of what happens in the firmware code would be if asked to perform an action in the code like dividing by zero.

This type of error can be caused by invalid print commands, corrupt data, or invalid operations. http://bsdupdates.com/printer-error/printer-error-code-49-3048.php The printer froze at 20 percent. There might have been a print job sent to the printer before you started the scan. If nothing else works...Follow the final step The last step is replacing the formatter assembly, which is the main logic board in these HP LaserJet printers.

Power the printer On and verify it reaches a READY status. Web Jetadmin can be used to clear these settings as well. No more errors for us. navigate to this website Press the Checkmark button once so that the letter R is highlighted.

Release the check button when the Ready, Data, and Attention light are on steady. The 49 series errors are firmware errors, you may need a new formatter pcb. Defective RAM will record bytes incorrectly at the damaged locations.

Replace with HP DIMMs, if necessary.

HP Printer Support 39.649 προβολές 6:35 Fixing a 49 or 79 Error on HP Printers - Διάρκεια: 1:16. If not, there is problem with the cleaning mechanism within the cartridge. Suggested Solutions Title # Comments Views Activity Connecting APC UPS 2200 via serial port 3 32 26d Sonicwall TZ205 configurable to utilize two WAN connections? 1 26 25d Zebra label printing Press(Down Arrow) button once.

Scan takes too long time.....Fallow the below step... 49.XXXX printer error what can this mean?Descripti... InitializeNVRAMonly when absolutely necessary. cold reset 2. my review here Can be caused by invalid ...