Home > Printer Error > Printer Error 79.4165

Printer Error 79.4165

They have the same HP-code. I have the same question Request More Information Current Answers There are currently no answers that have been posted for this question. KEY, press the [Item] key to navigate ...exit the online help system on accessing the online help system. Join the community Back I agree Powerful tools you need, all for free. click site

Check pickup rollers and separation pad clean as needed. IIISi/4Si check the door open sensor flag, PS1. Try printing a job from a different software application. The printer says ready then. https://community.spiceworks.com/topic/279079-hp-4000-n-gives-a-79-4165-error-every-few-jobs

Leaking a lot of ink on the inside of 10/24/2016 10/24/2016 crash2199 Error on computer- print head colors or print head not 10/23/2016 10/23/2016 Nathan I am getting a ADF jam Even though the fuser is new, could the printer thinking it isn't cause this error? You can try to clean it up and sometimes removing the label and apply a small drop of oil will make it run again. I ran the paper path test, at the bottom of the page it says: Duplex: OFF.

characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 10025764 Search Fixya Press enter to search. But be carefull some solutions could end up costing you. Back back to top How did we do? Suchergebnisse werden angezeigt für  Stattdessen suchen nach  Meinten Sie  oder Stellen Sie eine neue Frage Frage Antworten Themen-Optionen RSS-Feed abonnieren Thema als neu kennzeichnen Thema als gelesen kennzeichnen Dieses Thema nach

If worn, replace. It is not specifically related to particular part numbers of fusers or duplex units.Replace the fuser or duplex unit with another to alleviate the 55 error. Back back to top Error 16 Toner Low Toner cartridge is empty or toner in cartridge is not distributed evenly. Error 58 4/4L/4P/4V/5/5P Check the fan cable - reseat cable or replace fan 4V/4MV Defective DC controller board - replace IIISi/4Si Error 58.1 & 58.2 Improperly seated paper cassette 4Si/IIISi 58.1/58.2

then they cry becuase it worked before and not now and its my fault. Tried to reset printer as instructed, but problem persists. Thank you and your firm again, you were terrific. Simplify the print job by removing font changes and/or graphics.

I searched HP's site and came up with nothing. http://www.fixya.com/support/t14447740-79_4165_printer_error_laserjet_4050 FINISHER OUT OF BINDING AGENT FINISHER ALIGN ERROR [BIN NAME] FINISH LIMIT REACHED [... by dmzcompute on Dec 30, 2008 at 6:39pm Add comment Please sign in to comment 0 The printer does not give any error messages but it does not detect the duplexer. For example, 1 = fan motor 1.

by unknown on Oct 28, 2008 at 7:45am Add comment Please sign in to comment 0 As always check and verify that what you are using is within the quide lines get redirected here I have installed the driver (1 - HP Universal Print Driver for Windows PCL6 x64) but the printer is in ERORR when i print, i think is... Again on the LJII/III we are starting to see more and more failures of the gear drive assembly. Apr 03, 2008 | HP LaserJet 4050n Printer Not finding what you are looking for?

  1. at the front of this user's guide.) A temporary printing error occurred.
  2. Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot.
  3. Watch the termination's on the network cabling.
  4. I started screwing around with it, and eventually found that if I took out the duplexer, the printer no longer came up with the error.
  5. but yesterday there was a new error "79.4165 Printer Error".
  6. Replace as needed IIP S/N between 2925J00000 and 3047J99999 replace fuser assembly Back back to top How did we do?

The product was delivered just a few minutes ago. please call me. ERROR 67 Defective formatter PCA On the 4Si this could be a temporary error which can be corrected by cycling the power 4V/4MV - This can also be a temporary error navigate to this website Posted on Oct 22, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Leroy Elliott 3085 Answers SOURCE: Error message

These are one of the best most reliable printers in the market. Verify that the SIMMS or memory cards are seated. When you run the paper path test one of the obtions should be duplex on or off.

On some printers you can press the select button to try to continue.

Back back to top How did we do? LJ8100/8150 A fan motor failure occurred. Check Out the Latest Printers Report View all Fixya Reports Top HP Printers & Copiers Experts kakima Level 3 Expert 93922 Answers k24674 Level 3 Expert 7983 Answers Brian Sullivan Level Slide the blue fence at the back away from the paper (toward the back of the tray) then slide it back to the correct position for the size of the paper.

Defective MIO Card - Replace card Defective Formatter Card - Replace card Back back to top How did we do? Then put the printer back online and send a test job from the host computer via the parallel cable. It's most likely the card, however it could also be the formatter. http://bsdupdates.com/printer-error/printer-error-59-99.php The printer was constantly giving an Error 55.A.

by nivek on Oct 28, 2008 at 8:09am Add comment Please sign in to comment 0 I've got a error coming up when I switch a printer saying printer error 57.6 Add × Loading... EN Control Panel - 3 KEY, press the [Item] key to ... X represents the fan motor number associated with the error.

This prevents ink being left in the printer heads and nozzles, and will generally give your printer more life. Also verify the configuration through the menus on the printer. Thank you for the speedy shipment and response. HP LaserJet 4050, 4050N, 4050T and 4050TN Printers - User's Guide - Page 252 ...regulations E-1 features, printer 2 feeding paper, problems with 122, A-7 file directory B-4 Finland laser statement

The printer is getting quite old now and I had to shake some bits out of the fuser a while ago. PRESS GO TO CONTINUE 56.x PRINTER ERROR alternates with A temporary printing error occurred. We sell maintenance kits, fuser, repair parts and supplies.

Error Codes Error 10 - Supplies Memory Error 10.XX.YY Exact format is dependent on printer model The printer is unable to Vielen Dank dafür.Lösungsanfragen via privater Nachricht werden in der Regel ignoriert - bitte das Forum nutzen.

XXX-XXX-XXXX. Grüße-------------------------------------------------Hilfreich gewesen ? Note Press [Go] to navigate through a sequence of instructions.