Home > Printer Error > Printer Error 55.8

Printer Error 55.8

Cycle power. 4. DC Controller PCA malfunction.
12 OPEN or NO TONER or NO EP IIP/IIP+/IIIP Only: 1. Replace MIO card. 3. Reset by pressing the continue key. 2. click site

You did no damage switching formatters. Same as 42 error. 49 FIRMWARE ERROR Only for the laserjet 4100: Try printing a different file if error persists remove all dimms and EIO devices, last replace formatter. 50 ERROR If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services. Check tabs on side of toner cartridge. http://fixyourownprinter.com/posts/15223

Paper Control PCA malfunction. 4V/4MV Only: 1. FUSER? Check/reseat cable between DC Controller and Formatter PCA. 56 ERROR IID, IIID Only: 1. Privacy Policy Terms of Use Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming

  1. Tarr is University Distinguished Professor Emeritus at Illinois State University.
  2. Check front panel settings. 3.
  3. Of these the most famous were those On Heroes, Hero-Worship, and the Heroic of History delivered in 1840 and published in 1841.
  4. Respond to this 0 All I can tell you is that they have different part numbers which usually means there is a difference.
  5. First thing to try would be the formatter as it's a lot easier to replace.
  6. Sponsored by Ralph Waldo Emerson, it was first printed as a book in Boston in 1836 and immediately became the inspiration for the Transcendental movement.

Replace DC Controller PCA. 3. The problem is HP makes 3 different fusers which look identical, but the 3 fusers are not interchangeable between printer models. Post to the troubleshooting forum or Search the forums! Check RAM expansion card, reseat if necessary. 2.

It tries to initialise, but hangs up and just whirrs. He is the editor of a number of books on Thomas Carlyle and Marjorie Kinnan Rawlings, most recently Max and Marjorie: The Correspondence of Maxwell E. This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. Replace Scanner Assembly.

Paper path door open. 2. Obstruction in paper path. 2. Troubleshoot a problem Software and drivers (21) Windows (9) Macintosh (11) Other (Unix, Linux, Novell, etc.) (1) Installation and configuration issues (8) Printing (2) Windows (4) Other (Unix, Linux, Novell, etc.) As soon as you let go of the "Go" button it goes straight from "cold reset" message to the "79.00FE" message.A search suggests that it is a bad formatter, and I

Cycle power. 2. http://www.printertechs.com/printer-troubleshooting/367-50-5-error-on-laserjet-4200-4240-4250-4300-4350 Replace fuser. 2. Check Fan 1, replace if necessary. 57.3 ERROR 1. A cold reset doesn't do anything, in fact it will not even go through the steps of a cold reset.

Replace PostScript ROMs. get redirected here III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card. I/O config for the computer or printer is incorrect. 2. Check paper pickup rollers.

The formatter is universal, while the DC controller has to be the right voltage. The part of the top door that pushes the Plunger down is broken. 13 PAPER JAM 2686 Only: 1. Defective Interlock Switch Assembly. 4/4M/4+/4M+ Only: 1. navigate to this website Disassemble clutch and re-grease.

Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations Sign Up Login Add Question Bob asked Dec 31, 2003 at 1:17pm 0 HP DesignJet 4000 HP 4050 Hi,I have a 4050 laserjet that will only show a 79.00FE error message Check Fan 2, replace if necessary. 57.4 ERROR 1.

It slides right into the metal formatter "cage" and works perfectly, if you want the "Infared" connector to work you need to punch a hole through the "cage" to connect to

Flex the arms on the plastic output bin slightly to remove one side of the tray at a time. It would probably be cheaper to just buy a new printer. Rodger L. Bad laser unit or improper laser power setting. 2.

IIISi/4Si Only: 1. Front Door-open Sensor (PS402) broken or stuck. 2. Replace Fuser Assembly. my review here Home Forums Forums Quick Links Search Forums Recent Posts Projects Projects Quick Links Search Projects Most Active Authors Members Members Quick Links Notable Members Registered Members Current Visitors Recent Activity New

At least one of two tabs must be present. 3. All Rights Reserved. This edition of Sartor Resartus is the first publication of the work that uses all extant versions to create an accurate authorial text. By the 1840s, largely on the strength of Sartor Resartus, Carlyle became one of the leading literary figures in Britain.

Push the fuser firmly--listen for the sound of both blue levers clicking into place. For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable page protect. 22 ERROR/ I/O CONFIG ERROR 1. Plunger missing on top cover. 2. If a duplexer is installed, remove it from the back of the printer.

Check tansfer roller.