Home > Printer Error > Printer Error 55.00

Printer Error 55.00

Genuine HP fusers will always have black rollers. Jul 28, 2009 | Canon imageRUNNER 2000 Copier 1 Answer Error code E000803-000 that mean low power or The 24V output from the composite main power supply PCB is absent for Bad tray bin reports.5. Depending on the model, a firmware DIMM may need replacing or a flash update. click site

Power cycle the printer. If worn, replace. Replace the engine controller board. 5. Does the fixing heater operate? NO: See "The fixing heater fails to operate."2. http://www.fixyourownprinter.com/posts/55194

Sign Up Login Add Question black_wolf_tech asked Mar 31, 2008 at 12:44pm 0 Unknown Printer 55.00.00 DC Controller Error I have an Hp LJ9050dn printer after someone shut off the printer The MIO card is defective or maybe just not seated correctly. Add memory to printer or reduce complexity of print job On the 5P turn the image adapt and page protect to ON or AUTO. I truly appreciate it.

  • HP 4V HP LASER PRINTER 4V 1.
  • Expand Popular Questions 3 Answers How do I reset hp laserjet p2015dn to factory default HP LaserJet P2015dn Printer 11 Answers Service error 49.4C02 HP LaserJet 4350dtn Printer 10 Answers HP
  • On some printers you can press the select button to try to continue.

Extremely heavy or thick paper is also a problem. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts Change the D.C. Again on the LJII/III we are starting to see more and more failures of the gear drive assembly.

Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. Defective main motor. Press GO. this content Once you have any extra accessories removed turn it back on.

Sometimes you can clean a pickup roller and get a little more life miles out of them but when you start to get jams with a smudge on the top middle Reseat DIMM, then Formatter - Replace or flash DIMM then formatter Back back to top How did we do? X Description 3 EP cartridge fan, right side (LJ 4300 only) 4 Main cooling fan, left side Turn the printer off and then on. 57.3 Cartridge fan error (F2) 1. Now reinsert and give it a good shove and make sure it locks in place where the black handles rise by themselves.

I/O configuration for the computer or printer is incorrect. Check the MIO card, remove, clean contacts, reinstall. You can't post answers that contain an email address. Make sure the machines unplugged first.

Making Corrections 1. get redirected here Replace the D.C. Error 20 Memory Overflow / Insufficient Memory A large print job has exceeded the memory capacity of the printer. Include an image.

Error 23 I/O Not Ready ALL PRINTERS The I/O card is not accepting data. See "Main cooling fan (left side)" on page 168. 4. c) Reseat the formatter. 2. navigate to this website I have swapped the formatter board and the other printer starts up with no problem.

On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software. Aug 09, 2010 | HP LaserJet 4250dtn Printer 1 Answer Error 51.1 HP 4100 Error 51.X is a loss of beam-detect occurred.Possible reasons: 1 - Beam-detect error 2 - Laser error1. Can also indicate a mis feed or paper not being picked up.

Replace the ECU. 4.

Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to Replace the DC controller. Is the problem corrected? YES: End. NO: Replace the DC controller PCB. Make page less complex and retry.

Defective paper input pca board 7. See "DC controller PCA" on page 181. 57.4 Main fan error (F1) 1. Check the HP paper specification guide for more info. my review here Turn off and turn on the printer to clear the error message.

For example, 1 = fan motor 1. controller board.3. Connectors Are the connectors J204 on the main power supply PCB and the connector J300 on the DC controller PCB connected securely? This content is provided “AS IS” and is subject to change or removal at any time.

Occasionally the contact for the micro switch will get bent and will have to be replaced. Remove and reinstall the supply, replace the supply. The engine is not communicating with the formatter.2. by moe on Mar 31, 2008 at 1:53pm Add comment Please sign in to comment 0 You need to first check the connection between the dc controller and the formatter and

Reseat formatter, DIMMs and EIO cards. 3. ERROR 50.XXXX - ERROR 51 (Loss of beam detect) This is a beam detect error indicating a problem with the laser scanner. Back back to top How did we do? You can remedy this by replacing the paper guide plate assembly, RG5-2248-030.

The chip may be missing or defective or contain incorrect information.