Home > Printer Error > Printer Error 54.2

Printer Error 54.2

Performing a sensor test in Diagnostics Mode can test PS11:Enter the Engine Diags Path Sensors test as explained above. Once in fifty powers on of printer start without error. If there is no electrical continuity,replace the black toner cartridge on/off switch.8 Check electrical continuity between connectorJ642-1 (PYMC) and J642-2 (PBK) on thesubrelay PCA when the door switch (SW673)is turned on. After all are out I would turn on the printer and reinstall one at a time to see f that stops the error. click site

If I open the flap the cartridges are not in the release position - the handle is rotated down into the body of the printer. After you close the print cartridge door, the control panel displays the 'Calibrating or initializing' message. Figure 8: Copper piece inside the carousel assembly 1 - Screw 2 - Two clips on the copper piece Remove one screw (Figure 8, call-out 1). No obligation to buy! http://h30434.www3.hp.com/t5/LaserJet-Printing/My-HP-LaserJet-100-color-MFP-M175nw-is-getting-a-54-2-error/td-p/2973757

If there is no electrical continuity,replace the main relay PCA.10 Measure the voltage across connector J648-1(+24 VAR) and J648-3 (GND) on the mainrelay PCA after the printer is turned on. by unknown on Sep 8, 2011 at 11:36pm Add comment Please sign in to comment -1 I have to agree with Moe. I had a strange feeling about this machine.Driver installation was also a drama on a HP laptop (which was 1 week before reinstalled from scratch).

After you close the print cartridge door, the control panel displays the 'Calibrating or initializing' message. Also, the yellow print cartridge may have stopped at the top of the carousel. Repeat this process to remove each remaining print cartridge.6. While holding the release brake down, rotate the carousel forward or back to line up the black cartridge guides on the carousel to the proper position to remove the print cartridge(s)

by FA4nier on Sep 10, 2008 at 8:07am Add comment Please sign in to comment 0 These printers are better off being REPLACED since they are OLD. Replace as necessary.Close all drawers and the printer top cover, then turn the printer on.Wait for the printer to warm up. Cleaned & lubed 'em,put it back together, runs (and sounds) great. Once you have all the print cartridges removed you will need to turn the printer on.8.

See Figure 1, call-out 1. Before the carousel rotates it has to rotate that piece so that the highest section (the part that sticks out) is up. If PS11 is functioning, the value will briefly change to 1, then back to 0, as the cam returns to its home position.NOTE: If the value does not change, replace the Several things can be attributed to this error.

  1. When you disasembled, it simply lost the settings.Good luck in your quest.
  2. Probably something is blocking the croussel.
  3. No grinding noises or anything like that either, it just doesn't move at all.

Is this normal?Also, I want to be able to verify the operation of PS11, but can't find it.I have the HP Service manual, so feel free to reference it if you Spin it around one revolution to see if any of the cartridges are binding its movement. Error code list by brand Solving error 54.2 on HP printers This error is linked to a defective cartridge or carrousel. The issue can troubleshoot using the technique mentioned below.

if you press the button to rotate the carousel the carousel moves 5-10 cm and locks out. get redirected here It seems to me if you used enough force, you'd hear some awful noises. with and without toners installed? When they work right thay print out beautiful color pictures.

But now it works again, for now. For $150, I can probably put half a printer of brand new supplies in a new HP Color LaserJet, and it would probably last 3 months.I'll gladly sacrifice a little bit But message show me that wrong color in slot. navigate to this website I changed the carusel assy and then work fine.enzo by enzo on Sep 10, 2008 at 7:27am Add comment Please sign in to comment 0 These machine are old pieces of

The toner cartridges all enter correctly, they're all new...still showing error 54.2.Thanks in advance for any advice. I then vacuumed out all the toner inside the printer. by moe on Jun 24, 2004 at 9:40am Add comment Please sign in to comment 0 A couple of things come to mind.

I have done this but the printer still states intermittently Printer failure...."here is a problem with the printer or ink system.

Which part is the motor for the carousel? This error is typically accompanied by a loud grinding noise.NOTE: The carousel is the rotating part under the top cover to which all four print cartridges attach. (C = Cyan, M He/she describes it well and I believe this would solve his/her problem (mine was similar). This, of course, might not be the problen in your case.

Nevertheless, the device completed and seemed finally be ready . You'll look like a multi-colored Smurf. If thevoltage is not 24 V, replace the main relayPCA.11 Reconnect connectors J704 and J706 on thecarousel motor PCA, and connector J220 onthe controller board.12 Reconnect connector J43 on the carouselposition my review here Repeat this process to remove each remaining print cartridge.6.

You might check caroussel and driver for loose shrews, springs, ect by unknown on Jul 3, 2007 at 10:53am Add comment Please sign in to comment 0 I have that 54.2 Replacing the left-side cover with the strap on backwards bends the strap into the carousel, preventing proper rotation and possibly causing a 54.2 error. Please!!!!! Reply 0 0 pcwizard Provost Posts: 12,147 Member Since: ‎12-31-2009 Message 6 of 25 (8,917 Views) Report Inappropriate Content Re: 54.2 Error on HP MFP M175NW Options Mark as New Bookmark

by Emeric7 on Jul 2, 2007 at 2:37am Add comment Please sign in to comment 0 it is not clear to me if you cleaned the sensors with a brush? Once they are all removed check to see if there is any foreign material inside the printer or paper. Just make sure you do not touch the toner magroller in the cartridgeswith your finger as the oil on your hands can cause damage to the toner mag roller. My 4550 produces excellent color and I am pleased with it.

My fix for the 54.2....the carousel bearing needed a couple of drops of plastic compatible oil and it loosened right up. Trick is you have to click the numbers twice and you can only download 1 part at a time.