Home > Printer Error > Printer Error 53.10

Printer Error 53.10

make sure you do a config page before you do that. Pressing the Select (check) button should clear the message. Print a Configuration page and check the printer settings to determine which values have changed. (To print a Configuration page, open the Information menu at the printer control panel and scroll Action Turn the printer power off and then turn the printer power on, if the error persists, contact HP or an authorized service provider. click site

Turn the MFP off, and then replace the DIMM that caused the error. When handling DIMMs, either wear an anti-static wrist strap or frequently touch the surface of the DIMM anti-static package, then touch bare metal on the printer. HP COLOR LASER PRINTER 4600, 5500 ERROR CODE 53.XY.ZZ 1. I need to connect a Minolta DiMAGE Scan dual III AF-284D to 10/22/2016 10/22/2016 Jason Jones I just changed ink cartridge and now I get error code C000 10/22/2016 10/22/2016 Jennifer

This is typically an e-label issue. Figure 34: Turning off and unplugging the printer Turn the printer so that its rear cover faces you. Description A stacker or stapler/stacker error has occurred. top 57.7 DUPLEX FAN FAILURE Description The cooling fan in the optional duplexer is not functioning.

Be careful not to spill it on yourself or into the printer.) NOTE: NNOTE: If the jammed paper is difficult to remove, try opening the top cover all the way to top 52.XY PRINTER ERROR For help press? You might be able to print pages that are more complex if you add memory to the printer. Unsupported memory size.

HP 10/22/2016 10/22/2016 Electronics Pete Rodin Artisan 810: one line is printing in pink, another 10/22/2016 10/22/2016 Shefin X Ask a Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 47 Technicians SIMM malfunction. 2. The DRAM DIMMS must be installed in synchronous pairs in adjacent slots, with the same size and speed in both slots. Refer to the following instructions for additional information about adding more memory: NOTE: If you have not already done so, print a Configuration page to find out how much memory is

Turning the printer off and then on can clear some of these messages. Figure 23: Pulling out on staple cartridge Rotate the green cover on the end of the staple cartridge upward and remove the jammed staple. Failure in front memory slot. 2. Figure 24: Removing jammed staple Insert the staple cartridge into the stapler unit and rotate the stapler unit toward the rear of the printer until the unit snaps into place.

  1. Your issue is a beam detect error with your laser scanner.
  2. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize.2.
  3. Turn the printer power off and then turn the printer power on.
  4. The menu map will print out.
  5. If the error persists, replace the DIMM.
  6. HP Recalls Find comprehensive HP recall information updated hourly on RecallOwl.com.
  7. If loose toner falls into the printer, it might cause temporary problems with print quality.
  8. Pull gently on the bin to make sure that the hinge pins are fully inserted.

Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework. Critical error messages Critical error messages display warnings about device failures. Means the DIMM you trying to put in slot is too many MB. Figure 16: Opening Tray 1 and removing entrance cover Rotate the paper guide to check for additional jammed paper underneath.

Figure 46: Pulling the cover on the right side of the printer Remove the cover from the printer. get redirected here Values of X and Y are as follows: X = DIMM type 0 = read-only memory (ROM) 1 = random-access memory (RAM) Y = device location 0 = internal memory (ROM If jammed paper is present, remove it. If the error does not clear, turn the printer power off and then turn the printer power on.

Set High Speed to No and Advanced Functions to Off. Figure 55: Setting the left guide Pinch the release that is located on the rear paper guide and slide it to the correct paper size. Plug the printer into a wall outlet and see if this resolves the problem. navigate to this website Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps.

Temporary dimm error 2. You might need to reseat or replace the specified DIMM. 3. If the above action does not solve the issue, contact HP or an authorized service provider.

I read the troubleshoot and knows that code means the Memory in the third DIMM slot has failed the RAM test.I changed the memory and also replaced the Formatter board.

If so, reinstall the duplexer. If the message persists, contact HP Customer Support. If the error persists contact HP or an authorized service provider. AUTO CONTINUE has two settings, OFF and ON (the default).

Turn the printer off and then back on. Open and close the top cover to clear the message. prev next 3 Points Related Questions: 2 Answers Show error 52.00 52.X PRINTER ERROR The laser scanner speed is incorrect. my review here Action Press the (Select) button to resume printing.

Figure 50: Pressing DIMM strait into slot Close the DIMM-access door. Turn the printer power off. Scroll to the System Setup submenu, and then scroll to either CLEARABLE WARNINGS or AUTO CONTINUE. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the electrical specifications for the printer. (See the printer User's Guide

Pressing the Select (check) button should clear the message. controller. Replace simm's chip. 3. To view Help for a message (if available), press (Help).

If the error message persists, contact HP support.