Home > Printer Error > Printer Error 50.1

Printer Error 50.1

Power cycle the product to determine if the error is persistent. 2. I have seen it happen. So I thought I'd write about the 50.1 fuser error and see what kind of response I get from this.Troubleshooting the 50.1 Fuser  Error  The 50.1 fuser error in the HP partsnow.com are few that sell you a refurb on advanced exchange. click site

This content is provided “AS IS” and is subject to change or removal at any time. Replace the DC Controller. Try swapping them both out. HP Q3655A Color Laserjet 3500/3700 110V Fuser KitTroubleshooting the 50.1 fuser error in the HP Color Laserjet 3500, 3550, and 3700 PrinterThe first is the power source.

Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc. Find Similar Products by Category (hp) Fusers-Maint-Kits (hp) Printer PartsLaserjet 8000/8100/8150 Series Product Reviews Write Your Own Review How do you rate this product? 5 stars (best) 4 stars 3 You did not mention if you swapped all of them at the same time or just one at a time. Any suggestions?

If the 50.1 Fuser error message returns, it's time to replace your fuser. Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand Open the 2000-sheet input tray transfer door (if installed), tray 1, and the right lower door assembly 4. BrokenPrinter1 79.278 προβολές 12:29 How To Rebuild RG5-6532 hp 8100n 8150n fuser PART 1 - Διάρκεια: 13:21.

Power Supply Removal in the HP 8100 and 8150 AC Access Cover 1. Click here to order a replacement low voltage power supply. We've missed you. http://www.printertechs.com/printer-troubleshooting/334-50-1-fuser-error-8100-8150 I took the old fuser to another LaserJet 8150, and it is working fine.

CAUTION: The link arm is under spring tension. As the fuser  ages they get minor scratches in the heating element causing it to take longer to warm up. Disconnect three connectors, and release one wire harness from the retainer. 3. Remove four screws. 4.

I replaced the fuser, DC control board, Ac Power supply, Fuser Cable and then I replaced the fuser again (to be sure). If the error persists, replace the ECU. 8. Sometimes this helps clear any errors stuck in the memory. Do not let the link arm snap back toward the product when you release it. 4.

Break in the main thermistor. get redirected here fastprintersdotcom 60.578 προβολές 6:44 RM1-1082 hp 4250 4350 Fuser film sleeve how to rebuild - Διάρκεια: 12:29. or its affiliates. Better to change ALL the maintenance kit parts at the same time as the fuser, than to just install a new fuser and have the new fuser damaged shortly after because

Duplex models only: Release two tabs on the duplex media-feed guide, and then slide the guide toward the back of the product to remove it. by msr976 on Dec 5, 2006 at 6:29am Add comment Please sign in to comment 0 Most of the time it is the Low Voltage Power Supply...And HP is providing free That is why the LVPS' are in short supply by unknown on Oct 29, 2004 at 5:40pm Add comment Please sign in to comment 1 I have swapped the formatter board, navigate to this website Related Products z Fuser Gear Kit hp Laserjet 8100/8150 $12.95 Paper Jam Kit hp Laserjet 8100/8150 $16.95 Fuser Roller Upper hp Laserjet 8100 / 8150 $29.50 z Fuser Locking Levers hp

This power supply is compatible with all HP LaserJet 8100 and 8150 series printers part numbers: RG5-4357, RG5-4300, C4265-69006, C4214-69020   The LaserJet 8100 and 8150 series printers are notorious for Metrofuser.com, depot-america.com. Find maintenence kitInstallation instructions Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Conditions Definitions Web Order

HP Q3655A Color Laserjet 3500/3700 110V Fuser Kit1.

CopiersOfficeEquip 21.503 προβολές 1:38 Troubleshoot HP 9040/9050 - Διάρκεια: 3:11. Click here to order a replacement low voltage power supply. The connector between the fuser  and the printer is not connected properly. Check the bushing by rotating the gears on the side of the unit.

I've written articles about problems I've seen  like the bypass tray and laser scanner problems. Make sure that the Fusing Assembly is installed correctly and is fully seated into its connectors (no bent pins or pins outside their receptacles). 2. Remove 7 screws Note: Make sure you remove the LVPS fan from the unit and put it on the new one before installing back in your machine. my review here Did you changed the power unit?

I don't know how many thank yous you get but here is one more. Carefully release the retaining tabs on the plastic panel to the left of the metal back cover by gently pulling the cover to the left while moving both pieces away from Open the lower-rear door, and then release one tab. 6. I am not sure is ac power unit has problem or not.

I HAVE THREE MACHINES THAT HAVE THE SAME PROBLEMTHANKSSALAR - Anonymous Here is my info C4267A Serial # JPBLL42413, can you tell me if this machine is in the service note Unplug 3 LVPS connectors 2. thank you very much video It's very helpful Posted by Unknown on 19th Jul 2012 thank you very much very helpful Showing reviews 1-4 of 12 | Next Customers Who Viewed Hold the release tabs on each side of the fuser by placing your thumbs on the top tabs (1) and your forefingers on the lower tabs (2).

HP P3015 NEW OEM Fuser, RM1-6274 Replacement Procedure Rear-door assembly Unplug Machine and let sit for 10 minutes to cool. 1. Notify me of new posts by email. 50.2 Fuser Error - HP Laserjet P4014, P4015, P4510 Printer Engine Test Botton Position in the HP Laserjet P3015 PrinterParts and Supplies StoreBrother Two of them were under heavy usage and had over 150,000 prints on them already and the fusing assemblies looked great. Sometimes the reboot will allow the fuser to reset itself and you can print a few more pages.