Home > Printer Error > Printer Error 49.1

Printer Error 49.1

Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. If error persists, replace the formatter. The line voltage and current source at the printer location might need to be inspected to ensure that they meet the electrical specifications for the printer. A switch on this assembly may not be activated properly. click site

Try a different software driver. 41.3 UNEXPECTED PAPER SIZE The printer detected a media size different from what it was expecting. Also, can I get some instructions on putting in the rollers. Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. On EX engine printers this error is caused by a bad PIU (paper input unit). 41.5 PRINTER ERROR The media reached the PS102 or PS103 sensor too early. 1. Continued

Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to Press GO to clear the error message and continue printing. 2. By using this site, you accept the Terms of Use and Rules of Participation Sign Up Login Add Question unknown asked Nov 3, 2009 at 7:38am 0 HP LaserJet 4100 prev next 1 Points Related Questions: 1 Answer Error 49.38.07 Power off the printer for a minute.

  1. by unknown on Nov 5, 2009 at 10:39am Add comment Please sign in to comment Please sign in to comment HP LaserJet 4100 Buy discount ink Buy this printer More HP
  2. Extremely heavy or thick paper is also a problem.
  3. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again.

Bad drive gears. You may be trying to print a document that is too complex for the printer's capacity (too many macros, soft fonts, or graphics). You need to check the configuration of your printer and drivers, reset the printer, try issuing an initialization command from within the application. If error persists, try printing a job from a different software application.

Replace a DIMM if you determine that it causes the error. 8. Finally, a failing formatter can also cause 49 errors.  There are certain models that are notorious for formatter failures, and there are other models where formatters basically never fail.   To be Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller. b.

On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software. disconnect the printer from all network points and cycle the power - when it is ready perform a path print test ( found under the diagnostics menu on the printer itself Back back to top How did we do? clear the print queue after powering off the printer.

Check for opens on the cable. If the problem persists when using tray 1, load media one sheet at a time. The information contained on this chip is dependent on the printer model and the supply. It can also be caused by a defective DC controller.

Also the paper feed/registration sensors could be knocked out of place. get redirected here Replace or clean as needed. If the issue occurs, please perform a restore factory defaults. Back back to top How did we do?

Let us know what you find! Use the arrow buttons to select Service, and then press OK. Defective Formatter PCA - Replace with known operational board and try again. navigate to this website On the 4P/5P printers, the top cover is open or no toner cartridge is installed.

Easily replaced after removing the top cover and three wiring harness connectors. How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols. Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot.

I/O configuration for the computer or printer is incorrect.

The page containing the error will automatically be reprinted if jam recovery is enabled. (Or, you might want to press CANCEL JOB to clear the job from the printer’s memory.) For The hex suffix gives more detail. Apr 03, 2008 | Brother MFC 210C All-In-One InkJet Printer Not finding what you are looking for? appears, and then release the buttons.

On the Laserjet 4/4+ an error 12 can indicate the top cover open or a broken tab on the cover assembly. This board takes the input from the two sensors and provides info to the DC controller. Submitted: 6 years ago. my review here On EX engine printers this error is caused by a bad PIU (paper input unit). 41.x PRINTER ERROR A temporary printing error has occurred.

Your ethernet cable going to the server could be picking up noise? The product was delivered just a few minutes ago. Los Altos Hills, CA Thank you. If this is successful, you have a problem with the optional I/O card and should replace it or reset it.

The MIO card is defective or maybe just not seated correctly. Reload the tray with the correct print media size. 2. ERROR 41-X X= 1,2,4,5 A temporary error occured - Press "CONTINUE" to clear. 41.3 Error - Unexpected paper size - more than one sheet of paper picked up. Turn off the machine2.

PDF Manual 201104201052F-350S-Owners-Manual.pdf.... The issue can be caused by a firmware error, invalid print commands, corrupt data, invalid operations, poor quality parallel cables, poor connections or specific applications. If you want to attempt board level repair try the electrolytic capacitor, C702, 10 uF 50 VDC. Suggested Solutions Title # Comments Views Activity printer preferences 4 39 106d ithaca itherm 280 gibberish print 2 38 66d Network printer becomes inaccessable randomly in 2012 R2 RDS sessions 1

Remove the card and reseat it, try swapping with a know good card from another printer.