Home > Printer Error > Printer Error 13.1

Printer Error 13.1

As the gear starts to turn power is turned off and the "L" arm returns against the gear assembly and when the opening is reached it stops the gear movement. I'll have to give it a try. Also make sure you close the cover firmly before sliding the tray back in to the printer. In that case, it was really stuck. click site

Pull the tray out, you are looking at the separation roller. Check also fuser and rear diverter assembly for jamming issues. 13.14 For Laserjet 5si. And write back. Checked paper settings..size/type...all is correct.

is paper lying flat perfectly in the tray when you open it after a print attempt? This happens about 3 to 4 times a week. 0 Question by:compdigit44 Facebook Twitter LinkedIn Google LVL 15 Best Solution byf-king And from HP : http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=67348&admit=-682735245+1171898750158+28353475 Go to Solution 5 Comments Used electrical tape to keep the flapper from clicking when it closes.She is printing perfectly and with all these new parts ought to be good for about 1 million more pages! picks up a blank piece of paper and then jams ..

it might print one page fine and then it spits out a blank page and errors out .. paper late jam. That's when we get out our "chingaderous stick". If this hasn't been happening too long, your feed/sep rollers are probably still OK.

If the separation clutch is too 'strong' it will push the paper back, look at the back of the printer to see if the paper gets pushed back, if it does Reply With Quote 01-16-2007,11:01 AM #7 Brian View Profile View Forum Posts View Blog Entries View Articles Senior Member Join Date Dec 2004 Posts 217 I believe the original poster said Never seen a sensor go bad, but that is the only thing left. I am thinking that its a sensor problem in the printer or the way the document was formatted that is causing it.

One feed roller is in the cassette tray and the other is right above it in the printer cavity. Ensure there is no obstruction in the path, such as a torn piece of paper. 5. If they are worn and they don't pick up the paper you will get a 13.1 and possible that they will pick the paper when you clear the error. I have seen where sometimes cleaning them with rubber rejuvanation fluid or warm soapy water can help and other times the complete itb tray needs to be replaced.

  1. by startrek133 on Nov 10, 2009 at 6:52am Add comment Please sign in to comment 0 Your responses are confusing, but from what i gather you have replaced the tray 2
  2. Blow into the flags there.
  3. I'll let you know.
  4. BrokenPrinter1 17.193 προβολές 4:25 what causes hp Laserjets Paper Jam and how to fix fast - Διάρκεια: 2:19.
  5. I have taken the printer apart to make sure of this.

Then just lift the top off of the tray assy. see this here paper jam from tray 3 after printing 10 or 11 pages..Do I need to change the roller kits..?? If you're interested in additional methods for monitoring bandwidt… Network Analysis Networking Network Management Paessler Network Operations Advertise Here 737 members asked questions and received personalized solutions in the past 7 Have cleaned and it still jams same spot.

Privacy Policy Site Map Support Terms of Use On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer get redirected here I thought it was worth asking before starting a new thread. Tray 1 and 2 print fine. Check the duplexer for proper operation.

ImagingTechnology 1.267 προβολές 0:56 hp Laserjet p2035 and p2055 how to remove and install a fuser PART 1 - Διάρκεια: 10:49. If needed replace fuser or appropriate drive gears, or both. 7. When printing on Trays 2 and 3, the printer will feed a blank sheet and then throw a 13.1 Paper Jam error. navigate to this website It has two video ports on it – VGA and DisplayPort.

Provide feedback Please rate the information on this page to help us improve our content. The Carter Hour 13.892 προβολές 18:42 How To Replace The hp Laserjet 4200n 4250n 4350n Swing Plate PART 1 - Διάρκεια: 5:50. All rights reserved.

All Rights Reserved.

it also says as the other guys say, check the rollers for wear. If I remove the seperation clutch it pulls paper just fine, but with it installed it gets a 13.1 there is no sound indicating that it is too tight. Be sure to lift the printer lid 100\%, because attached to the lid is a white plastic strap. Just use scissors and cut a 1/8"-3/16" strip of tape and place it over the solenoid strike plate where the foam was and put the L-arm and spring back in place.

Use canned air to blow out these. 1}Open top cover and remove the toner 2} Open the MP tray {front door} Remove the white plastic insert that has the green arrow If the clutch does not separate you have the new type and it will not be the issue. My 4000 had 13.5 error & did the 2" fall back thing. my review here by moe on Jan 5, 2010 at 5:13pm Add comment Please sign in to comment 0 Removed the tray2 cover and cleaned the solenoid.

Verify the media meets the specifications. 5. It is held in place by 1 screw. Just work the disassembly steps in reverse order to complete re-assembly and your done. Join & Ask a Question Need Help in Real-Time?

Covered by US Patent. I replace it with an adhesive backed felt strip that doesn't disintegrate, but dampens the noise like the sponge was originally designed to do. one under the registration assembly and one in front of the paper feed assembly, you can do it that way or take them out to clean them properly or to replace that is behind the MP assy.

Put the tray back into the printer and check if the paper level indicator moves. That causes the selenoid to stick and not return after each cycle and that is probably your issue.