Home > Printer Error > Printer Error 0502

Printer Error 0502

Now I can use my printer again! by unknown on Apr 5, 2011 at 9:08pm Add comment Please sign in to comment 0 my file is open contune by unknown on Jun 11, 2011 at 5:14pm Add comment Reply Laura says: 2009-12-08 at 10:14 pm This is SIMPLY amazing!! Press Select. click site

When you are done, simply close the cover, power back up, and see if it will print a test page for you.( In some, you will prompt it, in some it Gently slide the ink cartridge carrier to the middle of the printer.4. I let it soak for a bit, then carefully rinsed it with hot water on very very low setting.I cleaned up what dust I could and some ink on a plastic Reply Einstein says: 2007-01-27 at 12:14 am My encoder strip has completely fallen off my lexmark 4270. more info here

Thanks again! - Anonymous Worked for me & my lexmark x5150 made in 2003. :) RulEz!http://facebook.com/denis.trofimov - unknown 0 Did you find where the encoder strip is "hooked" on to? This mirror really helped to SEE what was going on back there.Anyway I have cleaned the rails, encoder strip , found the pen and still Hardware 0502. Reply Miguemex says: 2007-04-18 at 5:02 pm For Mike Miller: Since you found the solution for your printer problem and there are a few guys who got the encoder strip off.

  • Using an index finger, gently push encoder strip down and then back up to get it back into the slot located on the back of the ink cartridge carrier.NOTE: There is
  • I can print again!!!!
  • Reply Raz says: 2009-03-07 at 5:29 am Thans man your genius compare to those moron at Lexmark Reply Jano says: 2009-03-07 at 6:47 pm This site was really helpful in fixing
  • If the copy is satisfactory, repeat the test once to confirm that the error is gone.How to Perform the Hardware Test on the Lexmark X5150 ID:ENUS3744Using the operator panel on the
  • ciao ciao from Sicily Reply Dan says: 2007-11-10 at 8:35 pm That worked great!
  • A pit from a plum must have been on top of the printer when I was replacing the ink and feel inside.

So it's still getting the boot for an all in one photoprinter whose cartridges are cheaper. Pull each straight out using thumb and index finger on each side of each strip.4) In back casing, using a small phillips screwdriver, remove all four screws. lol thx for the info now i have a black cartridge missing when it's in there Reply Dot says: 2007-10-21 at 10:25 am I see I have joined an ‘elite' group. You're going to push and pop stuff and it sounds like your breaking it and you may just do that:0) UNPLUG IT AND REMOVE AC POWER BLOCK1) Remove scanner cover- it

Was about to throw the printer away and get a new one. I also have the problems that the printer grabs the paper from one side. Thank you! http://support.lexmark.com/index?page=content&id=SO2723 Thanks.

Name: * Phone Number: * Email: * Message: *

--> Skip to content Blog.forret.com Because eloquence is, like, whatever. I was 15 minutes away from buying a new printer. iYogi’s resolution rates are amongst the highest in the technical support industry. AND I THINK THAT THIS IS WHERE THIS ONE IS GOING TO.

It will become coated with the ink mist from atomized hot ink as the print jobs are performed. Limited Period Offer No card on file! I tried and tried to get it back on with no success. THANKS Reply Printer Wizard says: 2008-04-17 at 10:15 am This trick will work with all Lexmark printers but is best to use lint free cloth in pure alcohol for really stubborn

I just ran a Kleenex across it twice and that was all it took. get redirected here Reply Mike Miller says: 2007-04-14 at 8:59 pm I'd cleaned the rod with a paper towel and a little WD 40. When printing on my Lexmark x6170 the left side of the pages were always smudged and "missing" information. Thank you for requesting callback, we will get back to you soon.

Used alcohol.I unplugged all wires where I could see that they unplug and plugged them back in. Now I'm wondering if it was the tissue paper. The only solution to that is not put in a bulk of paper just about 10-20 papers and its fine…well good luck everybody and thank you for saving my lots of navigate to this website Reconnect the power cable and switch the printer on again. 11.

There is a ‘D' on one end and a ‘F' with a downward arrow on the other end. I have tried so many things and ended up insanely frustrated every time! So happy I didn't, thanks for this!!

Started when I innocently installed a new black cartridge ….

The error might be displayed as “hardware error 0502”. Reply Susan says: 2010-01-08 at 2:07 pm thanks - very helpful tip and you've saved me a lot of time stuffing around with my printer!!! Reply HAL says: 2009-10-17 at 10:15 pm I cant get my cartridge to move from left side. Then it seems to work better.

With a piece of tissue or a small artists brush…very lightly lubricate the steel rod and manually move the cartridge carrier back and forth 3 or 4 times applying a light by Anonymous on Feb 8, 2008 at 11:53am Add comment Please sign in to comment 0 the encoder strip is the see thru tape. Press the Power button. my review here I am not sure if it makes any difference at all which way it goes in.

Reply Auto says: 2008-12-13 at 2:37 am Thanks for the tip Had the 0502 error on a Lexmark all in one at the office that we use mainly for scanning I Reply Kim says: 2007-07-01 at 7:50 am Great my 76 year old dad (bless him) was having trouble and he wanted me to come round and fix it. Connect to Internet, devices and peripherals. If you are facing the printer and looking inside of the printer, the strip hooks to YOUR left with the arrow facing down.

Know Windows 8 a little better The new metro interface has changed lot of things in ... Will Microsoft’s new tablet give tough competition to iPad? Reply Tomás Borges says: 2009-12-15 at 12:22 am A minha empressora Lexmark X5150 ora dá error 0502 ou não im prime o papel A4 sai em branco. Google Docs' infamous "Moved Temporarily" error - fixed!

I really need the scanner as I have another printer. I have the same lexmark printer (6170). Thank you! I don't know what else to do.

After this, plug in the device and turn on the printer for its operation.