huvster : I believe that is a incline motor error, unfortunately the motor is not made anymore. If either of these conditions occur the lower PCA needs replaced. Bad lift motor winding.6. BrowseBrowseInterestsBiography & MemoirBusiness & LeadershipFiction & LiteraturePolitics & EconomyHealth & WellnessSociety & CultureHappiness & Self-HelpMystery, Thriller & CrimeHistoryYoung AdultBrowse byBooksAudiobooksComicsSheet MusicBrowse allUploadSign inJoinBooksAudiobooksComicsSheet Musicprecor error codesUploaded by fgwoodSpeedSensorAlternating CurrentElevatorTreadmill448 viewsDownloadEmbedSee MoreCopyright: check my blog
Corrective Action Disconnect the keypad cable from the upper PCA. Inspect all wiring and connections related to the lift position sensor (potentiometer). replied3 years ago. Question about 9.31 Treadmill 1 Answer My Precor 9.31 has error 42 displayed and will not go away by holding down the QuickStart button;what is the next step? ...Precor Error Code
If the reading makes large changes or is erratic, the lift position sensor (potentiometer) is likely bad. Generated Mon, 24 Oct 2016 10:24:52 GMT by s_wx1202 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection The error would usually occur when the lift was already in motion (usually downward) when a lift command in the opposite direction (upward) was made. Precor Error 82 If an Error 42 has occurred, it is important to know the physical position of the lift when the error occurred.
The incline is absurdly high, so I think that's ... i unplugged the 2 wires atop the motor but still got the error. Possible Reason: Bad or intermittent connection in the lift motor controller. http://www.fixya.com/search/p1141705-precor_efx_546i_elliptical_version_4/error_42 It is possible the lift is physically out of range or jammed.
If the error continues to re-occur, replace the lift motor. 2. Precor Error 22 If the Error 05 still appears, the upper PCA* is the cause and should be replaced. *Upper PCA's most commonly do not come with software. Bad lower PCA.4. Answer questions, earn points and help others Answer questions Manuals & User Guides Have a manual for Precor EFX 546i Elliptical Version 4?
If the Error 05 is eliminated, the liquid was the cause. http://www.fixya.com/tags/precor_error_42 I wish it was more positive but I still appreciate your help. Expert: J.T. Precor Treadmill Error Codes Using your model and serial number, use this link to view a service manual with procedure instructions. Precor Error 40 If the Error 42 condition is intermittent, a connection issue is probably the cause.
Include an image. click site Search Fixya Press enter to search. Thanks Jen Precor Error Code 42 Error Code: 42 Manufacturer: Precor Model: All Models Error Description: Error 42, Lift Position Value Out of Range. so no matter what your looking at a hefty price tag or a new unit.huvster : I think your computer may be having issues with this chat, im going to switch Precor Treadmill Error 29
A good capacitor will read AC peak voltage while an open capacitor reads AC RMS voltage. Blown lift fuse in lower PCA. 2. Calibrate the lift motor per the proper procedure for the unit being serviced and reattach the lift motor to the ramp (elliptical) or lift platform (treadmill). news Wipe away all liquid from the touch sensitive display.
Using the appropriate service manual for the unit being tested, refer to the lift calibration procedure. Precor Treadmill Error Code 82 Capacitor can also fail in the open condition which would result with the lift motor trying to run but not having normal power. Lift Position Value Out of Range Precor Error 42 Aug 15, 2011 | Precor EFX 546i Elliptical Version 4 1 Answer Efx 546 in diagnostics mode, flashes 255 and then real
Bad lift capacitor.5. Some lift motors used in production exhibited a very long turnaround time and the lift motor would still be moving in the original commanded direction while the control system was trying replied3 years ago. Precor Lower Pca solution?
getting error 42 when first turning machine on. If the Error 42 condition is intermittent, a connection issue is probably the cause. Replace the interconnect cable if necessary. More about the author This is definitely true if the Error 42 occurred while the lift was within its normal physical range.
Replace the capacitor if the reading is significantly low. The usual result is that the lift will be physically jammed as explained above, and probably also being cause for the lift fuse to blow. If this happened, the lift would not operate in one direction. It is a rare condition, however if the lift moves in the opposite direction commanded, replace the lower PCA.
The incline is absurdly high, so I think that's ... sometimes you get lucky with cheap parts on there.... View Most Popular EFX 546i Elliptical Version 4 Elliptical Trainers Related Question My precor efx 546 makes noise like a squeaking in left pedal it seems I tried to tighten pedal I know they are both 250V.
Disconnect the capacitor from the lift motor and test. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Corrective Action Bad or intermittent connection of the lift position sensor (potentiometer) is the most common cause of the error 44. Please enter a valid email address.
Precor Error 45, Lift Moving in Wrong Direction Probable Cause 1. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Corrective Action Check the lift fuse from the lower PCA. If the Error 05 is eliminated, the keypad is the cause and should be replaced.
Your Cart: Items Subtotal: $129.74 Continue Shopping Also Recommended: My Account | Quick Cart Login Username or email Password Keep me logged in Create Account Forgot your password? Please try the request again.