Your Own Question J.T., Technician Category: Exercise Equipment Satisfied Customers: 982 Experience: I have over 10 years experience in all fields of fitness equipment repair and service. 16229639 Type Your Exercise The lift motor requires calibration. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. An interface chip (IC) has failed in the upper PCA's keypad. 3. check my blog
Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual Manual-C80.pdf. Rafael Andrade/Demand Media Step 2Press the "ENTER" button three times to access the treadmill's error log. If the Error 42 condition is intermittent, a connection issue is probably the cause. demandmedia.com © 1999-2016 Demand Media, Inc. https://www.sportsmith.net/Categories.aspx?Document=007b400b-540b-43ca-9043-887a7253276c
They dont repair any boards, they just swap out bad parts.. This means the problem could be anywhere between the lift motor and the upper PCA. The lift motor requires calibration.
An interface chip (IC) has failed in the upper PCA's keypad. 3. Precor Error Code 40 Lift Position Value Out of Range Precor Error 42 Precor Error Code 40 sportsmith.net Does your Precor fitness equipment... Error 42 is displayed when the lift position reported by the ... Precor Error 82 Precor Elliptical Trainers precore error 40 546 error code investigate definition physical change definition 546 error 42 problems 546 code 40 repair true test error codes 546 upper View Less »
Filter By: pca lift potentiometer calibration upper motor position intermittent interconnect lower occurred bad physical range swap connection 233 questions posted Ask a Question Usually answered in minutes! Precor Error 15 Replaced Crank Arm on Precor EFX 546 and Display Doesn Work May 24, 2009 | Precor EFX 546i Elliptical Version 4 Not finding what you are looking for? Corrective Action Disconnect the keypad cable from the upper PCA. great post to read Using the appropriate service manual for the unit being tested, refer to the lift calibration procedure.
This means the problem could be anywhere between the lift motor and the upper PCA. Precor Error 22 If the reading makes large changes or is erratic, the lift position sensor (potentiometer) is likely bad. All-Star: An expert that got 10 achievements. Blown lift fuse in lower PCA. 2.
Most units have the lift capacitor mounted inside the lift motor, and others use external lift capacitors. check it out You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. Precor Treadmill Error Codes Swap the lower PCA with a known good lower PCA to verify if the lower PCA is bad. Precor Error 40 Typically it can be identified and tracked using an ohmmeter.
The lift motor potentiometer is bad. http://bsdupdates.com/precor-error/precor-elliptical-error-45.php The lower PCA is bad. Search Fixya Press enter to search. Error 42 is displayed when the lift position reported by the lift ... Precor Treadmill Error 29
If the intermittent connection cannot be found or corrected, replace the lift motor. Check continuity of the interconnect cable or swap with a known good interconnect cable to verify if cable is bad. Some lift motors used in production exhibited a very long turnaround time and the lift motor would still be moving in the original commanded direction while the control system was trying news you will hear the fan and other parts make noise but check the red and black anderson connection between the main circuit board and motor.
AC lift motors have a split winding (3 wires) and DC lift motors will have a single winding. Precor Treadmill Error Code 82 It is possible to see one of these messages displayed intermittently due to external causes. prev next 3 Points Related Questions: 1 Answer My precor efx 546 makes noise like a squeaking in left pedal it seems I tried to tighten pedal but I the whole
I am getting error 42 and was told to check these. I cant seem to get the elliptical to work. Simply recalibrating the lift motor will not solve the problem.] If the lift calibration number is not 0 or 255 and does not change when the lift motor turns, replace the Precor Lower Pca If the fuse is open, refer to steps 3 and 4 before continuing.
If anyone else has the speed error it might be worth a look to see if its the same problem. Generated Mon, 24 Oct 2016 10:25:50 GMT by s_wx1202 (squid/3.5.20) View all items Cart Subtotal: View Cart & Checkout 888-713-2880 Live Chat Equipment Parts Manufacturers AFG Assault Bowflex Concept 2 Cybex Epic Expresso Fitness Gear Freemotion Gold's Gym HealthRider Horizon Fitness More about the author Recommended Action: Intermittent connections can be difficult to locate.
Possible Reason: Bad or intermittent connection in the lift motor controller. Repair Parts for Precor EFX 546 Ellipticals SPORTSMITH net May 29, 2014 | Elliptical Trainers 1 Answer Precor EFX 546 05 stuck key Precor Error 05, Key Depressed at Power Up Tell us some more! Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete.
thanks Precor Error 40, No Lift Motion Detected Probable Cause 1. If the Error 42 condition is intermittent, a connection issue is probably the cause. Or just drag it here! The lower PCA is bad.
Has anyone had this problem. Bad lift capacitor. 5. Question about Precor Elliptical Trainers 1 Answer How do i solve error 42? ...error 42?