Home > Post Error > Post Error 6b38

Post Error 6b38

All that was plugged in was a USB keyboard. needed before control to E000 ROM A8 Control to E000 ROM A9 Init. I/O Card Parity Error at xxxxx An expansion card failed. if not, the message is I/O Card Parity error ???? weblink

Everything on that appears normal except the location says Port_#0005.Hub_#0003 I've never dealt too much with the Event Viewer. When I connect the ATX power connector to the motherboard, the system power on right away. crjdriver, Oct 16, 2006 #15 Sponsor This thread has been Locked and is not open to further replies. Please clear CMOS, re-install the memory and VGA card, and remove other USB, PCI devices.01 - 54 (except 0d), 5A- 60Problem related to memory. http://www.bleepingcomputer.com/forums/t/446671/asrock-6b38-error/

Back to top #14 James Litten James Litten ¿Ԁǝǝ˥q BC Advisor 1,928 posts OFFLINE Gender:Male Location:New Jersey Local time:03:50 AM Posted 20 March 2012 - 10:39 AM Those are not Vlad, I have the same issue that you had... some features that your BIOS has but they are closed by manufacturer of your motherboard. Rumpo-Stiltskin, Jun 6, 2006 #5 qldit Joined: Mar 18, 2005 Messages: 3,390 Good Evening All, it is possible that the previous PSU has taken something else with it to the happy

What should I be looking for? I thought it was odd so I restarted my computer. I even contacted ASRock through their web page for a fix but they never answered and there was no answer for this 6B38 error. Beep CodeDescriptions1 shortMemory refresh timer error.2 shortParity error.3 shortMain memory read / write test error.4 shortSystem timer failure.5 shortProcess error.6 shortKeyboard controller BAT test error.7 shortGeneral exception error.8 shortDisplay memory error.9

BLEEPINGCOMPUTER NEEDS YOUR HELP! ASRock 6B38 Error Started by MGallardo , Mar 18 2012 04:33 AM Page 1 of 2 1 2 Next Please log in to reply 17 replies to this topic #1 MGallardo Since it is still under warranty, return the board. Floppy setup ready to start 75 Floppy controller setup OK 76 hard disk setup ready to start 77 Hard disk controller setup OK 79 Ready to initialize timer data 7A Timer

I blogged that error at my other blog and realized that there is still no solution to that error what the motherboard gives as of today.That's why I'm writing this blog Failure at this point indicate a bad RAM chip, the 8042 Keyboard Controller or a data line DMA Chips The DMA registers are tested using a data pattern Final Initialization these In those cases, there is a problem with that particular post process. esta bastante bien saberlo la verdad. :| las asrock nunca son recomendables, dan bastante guerra en muchos aspectos.

Be careful or you may render your bios completely unusuable. You are the man!!! Note: Please do not clear the CMOS right after you update the BIOS. What's wrong?(4/15/2004) Answer:The MAC address of the on-board LAN is erased.

hope this helps Apr 25, 2011 | Packard Bell (181368) Motherboard 1 Answer Bios problem http://majorgeeks.com/BIOS_Patcher_d3965.html Find and fix errors in your system BIOS BIOS Patcher can find and fix errors have a peek at these guys Advertisement Recent Posts Malwarebytes "Unable to Access... In that a PS/2 keyboard won't work I would be suspicious there is other damage possibly M/B. BleepingComputer is being sued by Enigma Software because of a negative review of SpyHunter.

come back with his most recent findings....... Would I have to have a speaker attached to hear this beep test? After upgrading the BIOS, please reboot your system once then you can clear the CMOS if you need to do it. http://bsdupdates.com/post-error/post-error-200-299.php Back to top #4 the_patriot11 the_patriot11 High Tech Redneck BC Advisor 6,744 posts OFFLINE Gender:Male Location:Wyoming USA Local time:02:50 AM Posted 18 March 2012 - 07:39 PM hmmmmmm have you

que tengas instalado ). Have you tried contacting them yet? Nota : me ha pasado con un ratón de los baratos que puse para un chollo, aunque con cambiarlo de puerto ya funcionó ( sin necesidad de desactivar el USB Legacy

Guess not in this case.

Media Center: Motherboard: Gigabyte mp61p-S3, Processor: AMD Athlon 64 x2 6000+, Memory: 6 gigs Patriot DDR2 800, Video: Gigabyte GeForce GT730, Storage: 500 gig Hitachi, PSU: Seasonic M1211 620W full modular, Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

Why?(3/15/2004) Answer:This issue will happen if CMOS checksum is bad. Include an image.

Several functions may not work. Please press reset or clear CMOS.92 - 99Problem related to PCI-E devices. syyskuuta 2008 klo 13.38 Sheila kirjoitti... this content Would I have to have a speaker attached to hear this beep test?Click to expand...

Most of the time you connect a speaker to the board using the pin headers. The values stored in CMOS RAM are either corrupt or nonexistent. How can I do?(8/11/2009) Answer:Please kindly refer to the following suggestions: First, push the power button for three times. prev next 1 Points Related Questions: 1 Answer I'm unable to recover the bios error of Intel Desktop Board D845GLLY, even using the bios recovery file named NM0159.BIO.

If that doesnt work, go into the BIOS, load optimized defaults, and then again if it doesnt work do fail safe defaults. I let it sit there but nothing happens. Salu2! Back to top #12 the_patriot11 the_patriot11 High Tech Redneck BC Advisor 6,744 posts OFFLINE Gender:Male Location:Wyoming USA Local time:02:50 AM Posted 19 March 2012 - 11:28 PM I don't think

Thanks Something else I have noticed is that I do not hear any beep testing coming from the computer. Although Bios Central has used reasonable effort to ensure accuracy we are unable to verify all codes posted.