Home > Post Error > Post Error 301 Keyboard Error Hp

Post Error 301 Keyboard Error Hp

Contents

A fault code of 00 indicates that no problem was found. Ensure the ACPI/USB Buffers @ Top of Memory setting in Computer Setup is enabled. 162-System Options Not Set Configuration incorrect. Try rebooting the system. Quick Boot is a fast startup process that does not run all of the system level tests, such as the memory test. http://bsdupdates.com/post-error/post-error-304-keyboard-or-system-unit-error.php

Replace the system board. 404-Parallel Port Address Conflict Detected Both external and internal ports are assigned to parallel port X. Reconnect the keyboard with computer turned off. sometimes it will take u to a different screen asking u which system to boot, if that screen pops up turn off your computer, turn back on do the F1 thing Unplug the power cord, re-seat the memory modules, and reboot the computer.

1796 Sata Cabling Error

PRESS ANY KEY TO CONTINUE Originally posted by David_M 04-21-2003, 11:57 PM Anonymous (221551007) replied to Anonymous (221551001) Anonymous Keyboard Error 301 ?? Run Computer Setup. Remove any serial port expansion cards.

I have tried another keyboard that I know works(I am using it now) but I get the same message. To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module. Check to see that the processor is present. Post Error Codes Beeps stop after fifth iteration but LEDs continue until problem is solved. 7 System board failure (ROM detected failure prior to video).

Reset the date and time under Control Panel (Computer Setup can also be used). Hdd Controller Failure Replace the system board. 103-System Board Failure DMA or timers. Replace system board if minimal graphics degrading is an issue. 912-Computer Cover Has Been Removed Since Last System Startup Computer cover was removed since last system startup. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01037792 Full Boot may also be enabled to run every 1 to 30 days on a regularly scheduled basis.

Replace the graphics card (if possible). 510-Flash Screen Image Corrupted Flash Screen image has errors. Beeps stop after fifth iteration but LEDs continue until problem is solved. 5 Pre-video memory error. Reinstall tape drive or press F1 and allow system to reconfigure without the drive. 611-Primary Floppy Port Address Assignment Conflict Configuration error. If the problem persists, replace the RTC battery.

Hdd Controller Failure

Reseat fan cable. Replace the keyboard. 1796 Sata Cabling Error If the problem persists, replace the system board. 1796 Sata Cabling Error Solution None System unable to power on.

As I can manouver fine through the the Setup screens (that appear after the error message comes up) with the keyboard, I am pretty sure the keyboard is not the problem. http://bsdupdates.com/post-error/post-error-200-299.php Reflash the system ROM with the latest BIOS image. 511-CPU, CPUA, or CPUB Fan not Detected CPU fan is not connected or may have malfunctioned. To disable the Drivelock feature, enter Computer Setup, change Storage > Storage Options > SATA Emulation to IDE, and select File > Save Changes and Exit. Upgrade BIOS to proper version. One Long Beep Followed By Three Short Beeps

If fan is plugged in, but is not spinning, then replace heatsink/fan assembly. Beeps stop after fifth iteration but LEDs continue until problem is solved. 7 System board failure (ROM detected failure prior to video). The speed at which the computer loads the operating system and the extent to which it is tested are determined by the POST mode selection. weblink Make sure the memory module(s) are installed properly.

Reply Quote Take your coffee mug off the keyboard.  Originally posted by jmayer7 04-21-2003, 3:55 PM Anonymous (221551003) replied to Anonymous (221551001) Anonymous Keyboard Error 301 ?? All Rights ReservedAd Choices The information on Computing.Net is the opinions of its users. If the error persists, replace the system board. 2201-MEBx Module did not checksum correctly Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM.

Parity Check 2 Parity RAM failure or a PCI/PCIe device is asserting a SERR#.

Replace the processor. kybd buy another one as you can find one for under $20. Clean the air vents on the front, back, or any other vented side of the computer. RTC (real-time clock) battery may need to be replaced.

The only surefire fix is to replace the board. Continue adding devices one at a time to ensure all devices are functioning properly. Internal PXE option ROM is used for booting from the NIC to a PXE server. check over here This is a tutorial on how to fix it! - Διάρκεια: 5:51.

To manually switch to the POST Messages Enabled mode during POST, press any key (except F10 or F12). Reseat fan cable. Rearrange the DIMMs so that each channel has the same amount of memory. 219-ECC Memory Module Detected ECC Modules not supported on this Platform Recently added memory module(s) support ECC memory For systems with a graphics card: Reseat the graphics card.