Home > Beep Codes > Post Error Codes Compaq

Post Error Codes Compaq

Contents

In Computer Setup, set Advanced > Device Options > NIC PXE Option ROM Download to DISABLE to prevent PXE option ROM for the internal NIC from being downloaded during POST to If possible, replace the RAM IC. 1 long, 6 short Unable to load interrupt vectors: The BIOS was unable to load the interrupt vectors into memory. 1 long, 7 short Unable Unplug the power cord, re-seat the memory modules, and reboot the computer. Make sure the memory module(s) are installed properly. weblink

Reseat the graphics card (if applicable). For example, ‘3.5’ indicates 3 long red blinks and 5 short white blinks to communicate the processor is not detected. RayBay May 22, 2008 #14 Zed TS Rookie Posts: 20 Very nice job....I commend you on the effort you put forth for the betterment of us all. Logic board problem.

Hp Beep Codes

Reseat memory. Recreate the provisioning file using third party management console software. If possible, replace the CMOS or battery 15 Beeps CMOS RAM checksum error- The CMOS RAM has failed. If possible, replace the video adapter. 7 beeps (1 long, 1 short, 1 long, 1 short, pause, 1 long, 1 short, 1 short) AGP video: The AGP video card is faulty.

If the error persists after replacing memory modules, replace the system board. 213-Incompatible Memory Module in Memory Socket(s) X, X, ... Change the processor. 2200-PMM Allocation Error during MEBx Download Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. If the error persists, update to the latest BIOS version. Hp Beep Codes 6 Beeps Beeps stop after fifth iteration but LEDs continue until problem is solved. 11 The current processor does not support a feature previously enabled on this system.

Reset the date and time under Control Panel (Computer Setup can also be used). Hp Beep Codes 5 Beeps They indicate problems such as bad memory, bad keyboard or bad motherboard. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading... navigate to this website Replace the system board. 501-Display Adapter Failure Graphics display controller.

Network Server Mode Active and No Keyboard Attached Keyboard failure while Network Server Mode enabled. Hp Beep Codes 1 Short 1 Long Red Power LED flashes nine times, once every second, followed by a two second pause. Reset CMOS. You can use these codes to help troubleshoot issues related to system startup.

Hp Beep Codes 5 Beeps

Reboot the computer. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c02032573 Beep Code Descriptions 1 short DRAM refresh failure 2 short Parity circuit failure 3 short Base 64K RAM failure 4 short System timer failure 5 short Process failure 6 short Keyboard Hp Beep Codes The white LED blinks to represent the minor error category (short blinks). Hp Laptop Beep Codes Reseat the graphics card (if applicable).

For optimal performance, the SATA 0 and SATA 1 connectors must be used before SATA 2 and SATA 3. have a peek at these guys If the error still persists, replace the system board. 2217-ME Firmware Version request failure ME firmware is not properly responding to BIOS query for version information. Replace the video adapter 1 long, 3 short Video memory test failure- The video adapter's memory has failed. Reboot the computer. Hp Led Codes

OR The heat sink/fan assembly is not properly attached to the processor. The D-LED will hang if the memory module is damaged or not installed properly 00 ** Decompressing BIOS image to RAM for fast booting ** 0* Initializing Keyboard Controller 0* 0* Reset CMOS. check over here Proper voltage setting depends on your region.

High Tone, four higher tones. Hp Beep Codes 3 Beeps Reboot the computer. Not all diagnostic lights and audible codes are available on all models.

Turn off the computer.

Make sure the memory module(s) are installed properly. Replace the IC if possible 4 Beeps Keyboard error- The keyboard controller IC is faulty or the keyboard is faulty. Replace thermal sensor. Hp Compaq Beep Codes 4 Beeps If the system enters the POST, then power off and replace one device at a time and repeat this procedure until failure occurs.

High frequency beeps while running Overheated CPU- Check the CPU fan for proper operation. The computer will beep once after a POST text message is displayed on the screen. It allows you to configure specific parameters about the hardware in your computer such as time, date, disk drive parameters and other device settings. this content Press the F1 key to save the memory changes. 164-Memory Size Error Memory configuration incorrect.

If the error persists, replace the system board. 2211-Memory not configured correctly for proper MEBx execution SODIMM1 is not installed. Reseat rear chassis fan. If problems are found while booting, you can usually diagnose them using the error codes displayed on the screen. RTC (real-time clock) battery may need to be replaced.

Replace front chassis fan. 515-Power Supply Fan not detected Power supply fan is not connected or may have malfunctioned. Replace the IC if possible 3-3-1 CMOS RAM power bad- Replace the CMOS battery or CMOS RAM if possible 3-3-2 CMOS configuration error- The CMOS configuration has failed. May 24, 2008 #16 Maccs TS Rookie Excellent work . Search all support All Support Software, Drivers and Updates Troubleshooting How to Product Information User Guides Cancel Example: “Laserjet P1102w driver” or “HP Pavilion 17-f002na will not turn on” Loading Results

If able, test known good CPU. Complementary Content Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones If the processor fan is not spinning, make sure the fan's cable is plugged onto the system board header. If the error persists, replace the system board. 2201-MEBx Module did not checksum correctly Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM.

If fan is plugged in, but is not spinning, then replace heatsink/fan assembly. Replace the power supply. A basic function might be reading memory, displaying video, or being able to send information to a hard drive. Powers on, no tone.

BIOSStandard beep codes for computers using American Megatrends Inc. (AMI) BIOSs are listed in Table A.Table AAmerican Megatrends Inc. Red Power LED flashes seven times, once every second, followed by a two second pause. Test known good component. This page requires Javascript.

LED blinks four times Graphics Graphics controller not functional Test the system board with the minimum hardware and reseat all the connections and graphics cards. Reseat the card or replace it outright. This is because motherboard manufacturers reprogram codes to reflect their own customizations.